2 Tekniikka
Uusimmat viitteet
-
Formulation of a Composite with a Binder System using Microfibrillated Cellulose
(2021)Sekretess/secrecy/salassapidettävä (16/6/2026). -
Reduction of iron oxides with hydrogen
(2021)Iron is produced from iron ore in one of two ways, either through a blast furnace, where coke is used as fuel and reduction agent, or by a direct reduction process. The blast furnace is currently dominating iron production, ... -
Potential Energy Crops and Their Utilization Technologies in Ostrobothnia
(2021)Det finns ett ökande behov att ersätta fossila bränslen med miljövänligare alternativ för att minska mängden växthusgaser som förorsakas av användningen av fossila bränslen. Detta betyder att användningen av förnyelsebara ... -
Reducing Carbon Dioxide Emission from District Heating in Finland by Implementing Modular Nuclear Reactors – A LCA Study of SMRs
(2021)Ett av de största problemen som mänskligheten har för tillfället är hur koldioxidutsläppen ska minskas utan att minska energiproduktionen. Ett av de mest populära lösningsförslagen är att öka andelen förnybara källor. Dessa ... -
GHG Value Chain Reporting in App Development
(2021)Calculation tools to help a company estimate their product or service emissions exist. Unfortunately, most of these are complicated, too simplified to be reliable or kept only for use of consultants. This creates a large ... -
Alkali chloride induced superheater corrosion – Impact of percentage of molten phase
(2021)World energy consumption has doubled in the last thirty years, and projections indicate that the energy demand will increase. Carbon dioxide is the most critical greenhouse gas generated by human activity, originating ... -
The potential of lignin as a maritime biofuel
(2021)In the 1940s, efforts towards lignin valorisation were triggered by high oil prices, but today, the motives are much more varied. The movement towards a greener future to combat climate change and the expected introduction ... -
Printing and spectrometric detection of active pharmaceutical ingredients on different surfaces
(2021)Printing of pharmaceuticals is actively researched as a tailored and flexible fabricating method, towards personalized medicine. Inkjet printing is considered as a precise dosing method and in this work, theophylline is ... -
Investigation of waste heat sources and their utilization in process industry
(2021)Waste heat is a commonly used term for such heat energy that is not utilized in the process but dissipates to the environment unused. Waste heat is a by-product which can be found in various streams exiting ... -
Methods for Researching the Stratification Phenomena and Parameters Effecting it in a Cavern Thermal Energy Storage
(2021)At the moment energy companies in Finland have invested in large scale thermal energy storage to improve the efficiency of their district heating systems. This means that energy that would otherwise have beenwastedis saved ... -
Identification of possible measures to increase radial shaft seal lifespan in thrust bearing units using root cause analysis
(2021)Det finns ett stort globalt intresse för att öka effektiviteten och samtidigt minska på utsläpp inom den marina sektorn. Vattenjetaggregat har en stor inverkan på effektiviteten hos ett fartygs framdrivningssystem. En ... -
Machine learning for predicting alkali salt induced high-temperature corrosion of superheater materials
(2021)Climate change due to human activities has caused a global desire to lower CO2 emissions in the hope of halting the increasing global temperature. For electricity generation, this means reducing the CO2 emissions by ... -
Production schedule optimization in an animal feed industry
(2021)This thesis focuses on the optimization of the supply chain for an animal feed plant, including product deliveries and the production schedule. A Capacitated Vehicle Routing Planning (CVRP) model has been developed to ... -
Study of the washing efficiency of hydrolysed kraft pulp with a washing simulator
(2021)Sekretessbelagd fram till 17.5.2026 -
Development of a microfluidic bead-based immunoassay
(2021)The purpose of this Master’s Thesis work was to develop a prototype of a fluidic analysis method based on Wallac Oy’s solid phase, two-site immunometric assay. Immunometric assays are used for detection and quantitation ... -
Measurement of electrostatic forces for in-line quality control of ceramic slip
(2021)In this master’s thesis, done in collaboration with Geberit in Ekenäs, the goal was to determine whether a new in-line measurement probe was suitable for monitoring and controlling the slip manufacturing process. The ... -
Lipase catalyzed chemo-enzymatic epoxidation of fatty acids using ultrasound as a process intensification method
(2021)The recent trend in switching from fossil to renewable sources in the production of essential chemicals has revealed novel methods within the concept of green chemistry. This work focuses on the epoxidation of oleic acid ... -
Implementing a UI automated testing system for RoKiX Windows GUI
(2021)With the growing demands of their software products and short production time, software companies are always trying to shorten the software delivery time. Performing various tests is a critical process to identify the ... -
Freight optimization
(2021)Automatiseringen av fabriker är ett världsomfattande fenomen som har växt från år till år. Det här är en av orsakerna till varför optimerade leverantörskedjor är allt viktigare, ekonomiskt men också med tanke på miljön. Den ... -
Degradation of polydimethylsiloxane in simulated industrial process environments
(2021)Polydimethylsiloxane (PDMS) is commonly used in the Kraft process as an anti-foaming agent, which is added during the pulp-washing stage, where the pulp is separated from the black liquor. Crude tall oil (CTO) is later ...
RSS 1.0